Collapsible buttstock similar to the current US GI M4 carbine stock provides convenient six-position length-of-pull adjustment to fit different-size shooters, including those wearing body armor. Ready to install on any standard AR-15 rifle or carbine lower receiver; includes buffer tube, receiver lock plate, lock nut, toe-mounted steel sling loop, carbine recoil spring and buffer. Buttstock is made from extremely tough, fiberglass-reinforced, injection-molded nylon to resist impact, heat, moisture, extreme cold, and most cleaning solvents. Steel lock nut has four square notches and pre-cut detents for staking to lock plate. Available with Mil-Spec (nominal 1.14″ O.D.) receiver extens Mfg: Brownells SPECS: Aluminum and fiberglass-reinforced, injection-molded nylon, matte black. 8 3/4″ (22.2cm) OAL collapsed; 11 3/4″ (29.9cm) OAL fully extended
Quality-made, original-style, chrome pin. Perfect for replacement of worn or damaged pins; great for building new rifles. Small collar fits all carriers. Mfg: Dpms SPECS: Steel, chrome. Fits AR-15 and M16.
Double Star’s Picatinny Rail Adjustable Gas block is in house from 6065 T6 aluminum and finished with a black hard coat anodize. The stainless steel adjustment screw is held in place with a brass tipped stainless steel set screw. The brass tip prevents damage to the threads on the adjustment screw. Mfg: Double Star SPECS: Material: 6065 T6 Aluminum. Inside Diameter: .750.
Machined aluminum free-float forends provides an exceptionally positive, non-slip gripping surface for the support hand to help ensure maximum weapon control. Easy-to-install, two-piece free-float design eliminates handguard stress on the barrel that can compromise accuracy. Use with rifle’s factory gas tube; if changing barrel length, purchase replacement gas tube of appropriate length. Rifle-model available in all-aluminum Ridged design or cobblestone-texture Overmolded rubber grasping surface. Mfg: Hogue SPECS: Rifle – 12 1/4″ (31.1cm) long, 2″ (5cm) diameter. Fits AR-15/M16 and clones with rifle-length gas system.
The 2-piece 9mm SMG buffer body is made of solid steel and utilizes three steel weights as well as a neoprene bumper. Included also is the three rubber disks, two between the steel weights and the third between the first steel weight and the front of the buffer body. The additional weight was added so slow down the incredible high rate of fire of the blowback SMG. This will also be found in early 9mm semi-automatic only carbines. This buffer should not be used in any 5.56mm carbines. Mfg: Colt SPECS: Fits 9mm AR15 rifles. Not for use with 223/5.56 or 308 rifles.
Snap-on USGI-type replacement for your carbine’s factory-original handguard is made of tough, fiberglass-reinforced, injection-molded polymer that delivers superior impact and abrasion resistance. The ridged gripping surface and top/bottom vent holes retain the weapon’s authentic military look, while an internal heat shield of lightweight aluminum protects your hand from barrel heat. Skinny models have standard-issue single-layer heat shield on upper and lower handguard. Skinny M4 model has narrower diameter for operators who prefer a minimal bulk handguard. Fits AR-15/M16/M4 with carbine-length gas system. Mfg: Double Star SPECS: Fiberglass-reinforced polymer, matte black. 6 1/2″ (16.5cm) long.Skinny Approx. 2 1/4″ O.D. at rear tapering to 2″ (5.1cm) O.D. at front. Single heat shield only.
This M16 USGI Magpul Follower and Spring Kit breathes new life into used or unreliable magazines. Kit available as singles or in a three pack. The Magpul Enhanced Self-Leveling Follower is a drop in replacement for the aluminum USGI 30-round magazine black or green follower.Featuring a patent pending 4-way anti-tilt design for increased feeding reliability, the Enhanced Self-Leveling Follower is made from a non-hygroscopic and self-lubricating polymer. The Brownells CS Spring follows government specifications for spring tension and diameter, but with the added benefit of corrosion and set resistance. Mfg: Brownells SPECS: Fits – AR-15/M16 USGI 30 Round Magazines.
From Double Star is the M4 16″ carbine upper assembly. Included with the assembly is a T-marked Flattop upper receiver assembled with M4 feed ramps, forward assist, and ejection port cover. The M4 profile barrel includes a front sight base assembly. It also includes a gas tube and the required roll pin. Barrel Nut not included to allow for your choice of handguard. Mfg: Double Star
Kits contain commonly-replaced AR-15 parts so you can have replacements on hand for refurbishing and repairing your rifle. Kits come with various mixtures of parts. All kits are sold separately. Mfg: Cmmg SPECS: Fits AR-15 rifles.